Meters and readings
Gas isolated at a smart meter visit: what happens next
Why an Octopus engineer may isolate an appliance or cap your gas at a smart meter visit, what the warning labels mean, and who fixes and pays for the repair.
Edited by Rob Gibbs. Published: . Guidance reviewed: .
Short answer
Before fitting a gas meter, the engineer does a tightness test to check the pipework and appliances for leaks. Since 1 October 2026 the allowed pressure drop depends on your installation and can be as low as 1 millibar, so a system that passed before can fail now. If one appliance is the cause, it is isolated and labelled; if the leak cannot be traced to an appliance, the whole supply is capped at the meter. Do not use it or turn it back on yourself: get a Gas Safe registered engineer to repair it (your landlord’s job if you rent). If you smell gas, call 0800 111 999.
Why an engineer isolates gas at a smart meter visit
Whenever a Gas Safe engineer installs a gas meter, they test the pipework and appliances for leaks. This tightness test measures how far the pressure in the system drops, in millibars (mbar). A drop above the permitted limit means gas could be escaping somewhere.
The limit changed on 1 October 2026. It used to be between 4 and 8 mbar, depending on the size of the meter. Under the updated standard, which Gas Safe enforces through the Institution of Gas Engineers and Managers (IGEM), the limit is worked out from the volume of each home’s installation and can be as low as 1 mbar. Octopus says that in October 2025 about 364 of its 40,000 gas installations, under 1%, had a drop that falls between the new and old limits.
One appliance isolated, or the whole supply capped
If the drop is too high, the engineer has to find the leak. They turn off appliances such as the boiler, hob or gas fire one at a time until the pressure holds. If one appliance turns out to be the cause, they recommend isolating it until a Gas Safe engineer you choose can inspect it, and the rest of your gas can stay on.
If the leak cannot be pinned to an appliance, for example because it is in the pipework, Octopus caps the whole system. That temporarily isolates the supply at your gas meter until the fault is fixed, so you may have no gas for heating, hot water or cooking until then.
What the warning label and notice mean
Engineers follow the Gas Industry Unsafe Situations Procedure. They attach a “Danger Do Not Use” label to the affected appliance or pipework and give you a warning notice describing the fault. The notice puts the fault in one of two categories, and a few other points are worth knowing:
- Immediately Dangerous (ID): a danger to life or property if left connected. It is disconnected with your permission and must not be used until repaired.
- At Risk (AR): one or more faults that could become dangerous. It is turned off with your permission and should not be used until fixed.
- If you refuse to let the engineer make a natural gas installation safe, they report it to the Gas Emergency Service Provider, which has legal powers to disconnect the supply.
- Being told something does not meet current standards is different: an older installation is not necessarily unsafe, and bringing it up to date is your choice.
What to do next
Octopus’s advice after an isolation, together with Gas Safe Register’s, comes down to these steps:
- Do not use the labelled appliance or pipework, and do not turn the gas back on yourself, until it has been repaired and signed off.
- Book a Gas Safe registered engineer to find and repair the fault. You can find one, or check an engineer is registered, on the Gas Safe Register website.
- If you rent, tell your landlord straight away: the repair is their responsibility.
- If you smell gas or suspect a leak at any time, call the National Gas Emergency line on 0800 111 999, day or night.
- If you have questions about the warning notice itself, call Gas Safe Register on 0800 408 5577.
- Once the repair is signed off, let Octopus know so it can arrange anything left over from the visit.
Who arranges and pays for the repair
Octopus’s engineer makes the installation safe but does not repair your pipework or appliances. Octopus says the fix is for a private Gas Safe engineer, and Gas Safe Register says that once you are told about an unsafe installation, it is your responsibility to make sure it is not used until it has been repaired. In practice, if you own your home, you arrange and pay for the repair.
If you rent, it is your landlord’s responsibility. The Health and Safety Executive says landlords must keep the gas pipework from the meter to the appliances in a safe condition, and all repairs must be done by a Gas Safe registered engineer. The pipe that brings gas up to the meter is the network operator’s, not yours or your landlord’s.
If someone in your home is older, disabled or chronically sick, or you have a young child, join Octopus’s Priority Services Register. It also offers a free gas safety check every 12 months, but only to customers who own their home and receive means-tested benefits, and who either live with a child under five, or are of pensionable age, disabled or chronically sick and live alone or only with others who are all of pensionable age, disabled, chronically sick or under 18.
Questions people ask
Why did the Octopus engineer cap my gas?
Because the tightness test found a pressure drop above the safe limit, which suggests a leak, and the engineer could not trace it to a single appliance to isolate. Capping the supply at the meter keeps your home safe until a Gas Safe engineer finds and repairs the fault.
My gas was fine before. Why has it failed now?
The rules tightened on 1 October 2026. The allowed pressure drop used to be 4 to 8 millibars depending on meter size; it is now worked out for each home and can be as low as 1 millibar, so a small drop that passed before can fail now. Octopus says under 1% of its October 2025 installs fell in that gap.
Can I turn the gas or the appliance back on myself?
No. Do not use a labelled appliance or pipework, or reconnect the supply, until a Gas Safe registered engineer has repaired it and signed it off. Using an installation marked Immediately Dangerous could put lives at risk.
Who pays to fix the leak?
The Octopus engineer only makes it safe. If you own your home, it is up to you to arrange and pay a Gas Safe registered engineer for the repair. If you rent, your landlord is responsible for keeping the pipework and appliances safe and must arrange the repair.
Can the engineer cut off my gas without my permission?
Gas Safe Register says engineers ask your permission to make an unsafe installation safe. If you refuse on a natural gas supply, they report it to the Gas Emergency Service Provider, which has legal powers to disconnect it.
What is the difference between Immediately Dangerous and At Risk?
Immediately Dangerous means the installation is a danger to life or property if left connected, so it is disconnected and must not be used until repaired. At Risk means faults were found that could become dangerous; it is turned off with your permission and should not be used until fixed.
Is my electricity affected if my gas is capped?
The isolation is made at the gas meter and covers your gas installation; it does not involve your electricity supply. Once the gas repair has been signed off, contact Octopus about anything from the visit that still needs doing.
Related guides
- How to see and download your smart meter dataWhere to find your half-hourly smart meter data from Octopus: in the app, through the free API, and with this site’s private usage tools.
- Octopus smart meter not sending readings: what to checkWhy a smart meter stops sending readings to Octopus, how to check it, and how to keep your bills and smart tariff on track while it is fixed.
- Your smart meter in-home display explainedWhat a smart meter in-home display shows, why a blank screen does not always mean a broken meter, and when you need one at all.
- SMETS1 vs SMETS2 smart meters: what is the difference?How SMETS1 and SMETS2 smart meters differ, why it matters when you switch supplier, and what it means for Octopus smart tariffs.
- Octopus meter reading: how to submit one and read every type of meterSubmit an Octopus Energy meter reading in the app, online or by email, read any meter, and sort out smart meters, estimates and wrong readings.
- RTS meter switch-off: what Economy 7 and storage heater homes should doThe Radio Teleswitch Service has ended. How to tell if you still have an RTS meter, what can go wrong, and how to get a free smart meter from Octopus.
Primary sources
- Fuelling the future: gas, meters, and the net zero mission — Octopus Energy; checked 2026-11-14. Published 1 October 2026, updated 5 November 2026, checked 14 November 2026: a Gas Safe engineer installing a gas meter does a tightness test measuring pressure drop on the pipework and appliances. From 1 October 2026 the allowed drop depends on the volume of the installation and can be as low as 1 mbar, instead of the old 4 to 8 mbar by meter size, enforced by Gas Safe through IGEM. If the drop is too high the engineer must find and isolate the leak, turning appliances off one by one; they recommend isolating a faulty appliance until a private Gas Safe engineer inspects it, and if they cannot isolate an appliance they cap the whole system, temporarily isolating the supply to the meter. Next steps: do not use labelled appliances or pipework until repaired and signed off; use a Gas Safe registered engineer for the repair; tenants: the landlord is responsible; gas emergency line 0800 111 999; Gas Safe Register 0800 408 5577. In October 2025, about 364 of 40,000 installs (0.91%) had a drop above 1 mbar but under the old limit.
- Gas appliance warning labels — Gas Safe Register; checked 2026-11-14. Checked 14 November 2026: an engineer who finds an unsafe installation follows the Gas Industry Unsafe Situations Procedure: find and fix the fault if possible, otherwise ask permission to make it safe by disconnecting it or turning off the gas to the affected part. They attach a “Danger Do Not Use” label and leave a warning notice. “Immediately Dangerous” installations are disconnected and must not be used until repaired; if you refuse on natural gas, the Gas Emergency Service Provider is told and has legal powers to disconnect. “At Risk” installations are turned off with your permission and should not be used until fixed. Contact Gas Safe Register with concerns.
- Gas Industry Unsafe Situations Procedure explained (factsheet) — Gas Safe Register; checked 2026-11-14. Factsheet dated 22 April 2024, checked 14 November 2026: once told of an unsafe installation, it is your (or your landlord’s or agent’s) responsibility to make sure it is not used again until repaired; the engineer should also tell the landlord. Older installations that do not meet current standards are not necessarily unsafe. Engineers make an installation safe, with your permission, by disconnecting it or turning off the gas to the affected part. Where the emergency service provider leaves a warning notice, it is your or your landlord’s responsibility to have it checked by a Gas Safe registered engineer.
- Maintenance – gas pipework (landlords) — Health and Safety Executive; checked 2026-11-14. Checked 14 November 2026: landlords must keep gas pipework in a safe condition, including all installation pipework from the meter to the appliances, normally through regular inspections and repairs; the service pipe up to the meter is the pipeline operator’s responsibility. Checks include a soundness (tightness) test of the whole system. All maintenance and repairs must be done by a Gas Safe registered engineer.
- Priority Services Register — Octopus Energy; checked 2026-11-14. Checked 14 November 2026: eligible customers can get a free gas safety check every 12 months if they own their home, receive means-tested benefits and either live with a child under five, or are of pensionable age, disabled or chronically sick and live alone or only with others who are pensionable age, disabled, chronically sick or under 18. Octopus’s Gas Safe registered partners arrange the visit; others are advised to have appliances checked annually.